Exactly How to Remove and Change a Bathtub.
Exactly How to Remove and Change a Bathtub.
Blog Article
Were you interested in critical info around How to Install a Bathtub?
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to employing a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new bath tub in your shower room if you have actually already purchased a new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list must make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the tap in place with the supplier provided backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, place the bathtub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will certainly resolve it right into its final position.
Preparing for the Setup
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about complications with moisture and also possible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our piece on Tools You Need to Install a New Bathtub . Thanks a ton for finding the time to read our blog. Appreciated our content? Please share it. Let another person discover it. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Page Report this page